Motors and Drives: AC or DC?

Tuesday - 14/08/2018 11:27
Today we’re so glad to present you about motors and drives: AC or DC
Motors and Drives: AC or DC?
Motors and Drives: AC or DC?
The end of the DC motors era
 
Due to their reliability and precise variable speed control, direct current (DC) motors have long reigned as the workhorse of industrial applications.
 
However increases in quality and productivity requirements of modern manufacturing processes plead for motors and drives for an upgrade that can cope with higher demands and narrower tolerances.
 
DC GEAR MOTOR
 
Since most of the DC motors’ drives in service were installed decades ago, their analog control technology has fallen short to meet these new precision demands, besides due to commutators, DC motors are not suitable for very high speed applications.
 
The rise of AC motors
 
With the imminent advent of digital technology to electrical motor Drives, advances in microprocessors, solid-state electronics and AC motor control algorithms (vector control) have lead AC drives to gradually take over the revamp of many applications once only addressable by DC drives.
 
Electric Motor
 
Moreover, as DC motors are expensive to purchase and maintain, AC motors have been now established as the preferred choice for most new applications, slowly driving DC technology out of market and therefore out of development too.
 
A sustainable alternative
 
Spite the reasonable phase out trend of DC drives technology, the engineering niche of electrical retrofitting has significantly grown. This retrofitting trend puts forward an interesting approach where costs are considerably cut down by reusing the existing DC motors and most of the power electronics in their drives.
 
Thus, since DC machines have proven to be long-lived, by just upgrading the analog control into a digital Front End, the retrofit harnesses the best of DC technology; some of the currently operating DC motors are close to be almost a half century old and have been retrofitted and reused to serve diverse industries in their lifetime.
 
Resisting evolution
 
This electrical retrofitting challenges electrical professionals to push their expertise to its limit in order to achieve minimum process downtime while performing the upgrade.
 
But in the other hand it relieves them from spending in new equipment and as well from the need to acquire new knowledge and experience over the AC drive technologies.
 
But is retrofitting DC drives resisting a necessary modernization or is it promoting a sustainable solution to the increasing demands of an intensively growing demand for productivity and quality?
 
Energy usage inefficiency of outdated technology
 
Even though reusing DC motors can presumably be a sustainable pursuit, these electrical machines’ power factor ranges from 0.5 to 0.85, while AC motors can do up to 0.95 over their entire speed range.
 
So depending on the nature of the application, upgrading into DC or AC technology, in the long run can produce completely varied results in terms of energy consumption efficiency and thus cost.
 
The bottom line
 
Both DC and AC drives can address the new demands of manufacturing industries. However, rather than automatically going down for the trending technology, which most debates lean for AC, proper analysis should be done per application to weigh the advantages and disadvantages of using either technology. Nonetheless, DC motors and drives are not, and will not any soon become, obsolete.
 

Total notes of this article: 0 in 0 rating

Click on stars to rate this article

  Reader Comments

Security Code   
online
  • Support

    Sales Manager

    +(84)923.886.133

    dolin@dolin.com.vn

    Sales 01

    +(84)918.26.11.44

    dolinvn@dolin.com.vn

    Sales 02

    +(84)941.976.189

    info@dolin.com.vn

    Sales 03

    +(84)923.886.191

    sales@dolin.com.vn

    Sales 04

    +(84)949.380.913

    dolinsales@dolin.com.vn

    Sales 05:

    +(84)987.246.757

    dolin@dolin.com.vn

Google+
Bestsellers
Software
CNC Machine
Construction and Land
Counter
  • Online50
  • Search engine3
  • Guest47
  • Today2,090
  • This month321,834
  • Total8,949,536
You did not use the site, Click here to remain logged. Timeout: 60 second